Here is how to ship a Haas VF-2 the right way: on air ride, fully covered and kept dry from pickup to delivery. Shops buy and sell this machine all over the country, and this featured shipment shows how Abound Transport Group moved one from East Tennessee to the Sacramento area of California.
What did this Haas VF-2 shipment look like?
A Haas VF-2 and two pallets, about 10,000 lbs, from East Tennessee to the Sacramento area of California on a Conestoga flatbed.
- Machine: Haas VF-2 vertical machining center
- Machine size: 101 × 99 × 101 in, 8,400 lbs
- Pallets: Two pallets, 800 lbs each
- Total weight: About 10,000 lbs
- Lane: East Tennessee to the Sacramento area, California
- Distance: About 2,300 miles
- Trailer: Conestoga flatbed, about 104 in inside height
- Mode: Partial truckload, no transloading
- Transit: About 6 days
- Result: Delivered on schedule, no damage reported
The customer picked a rigger from three contacts the Abound team shared and booked the same afternoon. The machine loaded just after 8 AM, photos went out before 9 AM, and the receiving riggers were unloading minutes after the truck arrived. Read the full Haas VF-2 case study.

Does a Haas VF-2 need an air ride trailer?
Yes. Haas strongly recommends an air ride truck to keep a VF series machine from getting jarred on the road.
A VF-2 has a precision spindle, ballscrews and a control cabinet full of electronics. Air ride uses air bags instead of steel springs, so less road shock reaches the deck. Not every truck has it, so say you need air ride when you request a quote, and the Abound team will confirm it before the load is booked.
Why should a CNC machine ship fully covered?
Because a machining center is built for a shop floor, not the open road. A full cover keeps out rain, road spray and grit.
A cross country run can see rain, snow and desert heat in one week, and road spray carries water, grit and winter salt right into an open machine. Covered does not mean a heavy tarp mashed against the sheet metal, though. Haas warns that heavy tarps and careless tiedowns can damage the machine, so use edge protection or a Conestoga frame that keeps the tarp off it.
How do you keep a CNC machine from rusting during shipping?
Dry it out, put a light coat of oil on bare metal, wrap it and keep it covered the whole way.
Rust starts on the bare steel: the table, the ways and the spindle taper. Haas even ships new machines with a rust inhibitor on those surfaces. Keep it simple:
- Drain the coolant and wipe the machine dry.
- Put a light coat of rust preventive oil on bare metal.
- Wrap it, with a rust inhibiting (VCI) wrap if you have it, and keep it covered.
- Let a cold machine warm up before you unwrap it so it does not sweat.

What trailer is best for shipping a Haas VF-2?
A Conestoga flatbed fits most VF-2s. A step deck or double drop gives taller machines more room, and both can ship fully covered.
Start with the loaded height. Most states allow 13 ft 6 in, and the deck counts. A 60 inch flatbed deck leaves room for about 102 inches of machine, a 42 inch step deck about 120 inches, and a double drop well of 18 to 24 inches roughly 138 to 144 inches. Check your route on the Abound height map.
Why is a Conestoga flatbed good for a Haas VF-2?
It rolls a tarp over a frame, so the machine is enclosed and nothing rests on the windows or sheet metal.
A Conestoga loads like a flatbed from the side or top, then closes into a covered box. This one had about 104 inches of inside height for a VF-2 about 101 inches tall, for a loaded height of about 13 ft 5 in, just under the limit.

More on this in tarp vs. Conestoga for CNC machines.
When should a VF-2 ship on a step deck?
When the machine on its skids is too tall for a 60 inch flatbed deck.
A step deck runs about 42 inches high, roughly 18 inches lower than a flatbed. It ships tarped over edge protection, or as a Conestoga step deck with about 116 inches of inside height.
When is a double drop the right trailer for a CNC machine?
When a machine is too tall for a step deck. The low well gives the most height room.
A VF-2 rarely needs one, but bigger machining centers often do. A double drop can be tarped or run as a Conestoga double drop to stay fully covered. See lowboy and RGN trailers and flatbed vs. step deck vs. RGN.
How do you prepare and secure a Haas VF-2 for transport?
Lock the axes with the Haas shipping bracket, drain the coolant, lift it right and chain the base, never the enclosure.
Your rigger or maintenance team usually handles prep. Haas says to install the shipping bracket even for short moves and to lift a VF-2 from the side with a forklift rated above the machine weight. Crate or palletize the tooling and loose parts.
On the trailer, the carrier chains the base to federal securement rules. Chains should never ride on sheet metal, windows or the control panel. Need a crew? See industrial riggers.
Do you need cargo insurance to ship a CNC machine?
Carrier coverage has limits, so check it and consider added cargo insurance for a high value machine.
Ask what the carrier’s policy covers before the machine loads, and keep loaded photos as a record of its condition. See Abound cargo insurance.
What did this Haas VF-2 shipment look like?
Real photos from the move: loaded, enclosed and dry.
Swipe through photos from this move →



Ready to ship your Haas VF-2?
Send the model, size, weight and both addresses, and the Abound team will plan an air ride, fully covered move end to end.
Abound coordinates CNC machine transport from Tennessee to California and across all 50 states through Armstrong’s network of 75,000+ carriers. See CNC machine shipping cost, how to ship a CNC machine and more real moves on the Featured Shipments page.
How to ship a Haas VF-2 FAQ
Quick answers from this shipment and Haas’s own shipping guidance.
How do you ship a Haas VF-2?
Lock the axes with the Haas shipping bracket, drain the coolant and protect bare metal from moisture. Then book an air ride trailer that keeps it fully covered, usually a Conestoga flatbed, with riggers at both ends and no transloading.
What trailer is best for a Haas VF-2?
A Conestoga flatbed fits most VF-2s. On this move the trailer had about 104 inches of inside height for a machine about 101 inches tall. Taller machines can go on a covered step deck or double drop.
Does a Haas VF-2 need an air ride trailer?
Haas strongly recommends an air ride truck for VF series machines. Ask for air ride when you request a quote, because not every truck has it.
How do you keep a CNC machine from rusting during shipping?
Drain the coolant and dry the machine, put a light coat of oil on bare metal, wrap it and keep it fully covered so rain, road spray and condensation cannot reach it.
How long does it take to ship a Haas VF-2 across the country?
This East Tennessee to Sacramento area move took about six days from pickup to delivery, including a holiday weekend. Transit times vary by lane, carrier and schedule.
Ship your Haas VF-2 covered and on air ride
Abound Transport matches an air ride, fully covered trailer through Armstrong’s carrier network, coordinates riggers at both ends and sends loaded photos before the truck leaves.
Talk with an agent at (800) 957-2558, Mon to Fri, 5:30 AM to 5:00 PM PST.
Sources
Official references and company pages cited in this guide.
- Haas Automation: Mill operator’s manual, shipping the machine
- Haas Automation: VF and VM series installation
- FMCSA: Cargo securement rules
- FHWA: Commercial vehicle size and weight overview
- Zerust: How to seal VCI packaging
- Abound Transport: Haas VF-2 case study
- Abound Transport: Conestoga trailers
- Abound Transport: Step deck trailers
![]()
Abound Transport Experts
The Abound Transport team is a family-operated logistics agency based in Southern Oregon. As an authorized agency of Armstrong Transport Group, LLC, we give every shipper one-to-one service from the first quote to delivery.
Never Miss an Update
Add aboundtransportgroup.com as a Preferred Source on Google.